Cisco vlan ip address

Here are the steps to configure an IP address under VLAN 1:

1. enter the VLAN 1 configuration mode with the interface vlan 1 global configuration command.
2. assign an IP address with the ip address IP_ADDRESS SUBNET_MASK interface subcommand.
3. enable the VLAN 1 interface with the no shutdown interface subcommand.

1. Does a VLAN have an IP address?
2. How do I find my VLAN details?
3. What is a VLAN IP address?
4. How many IP addresses are in a VLAN?
5. Does native VLAN need IP address?
6. How do I add a VLAN to my router?
7. Does VLAN have default gateway?
8. What is VLAN ID in router?
9. Why do you assign an IP Address to a VLAN?
10. What is VLAN in CCNA?
11. Should I use VLAN or subnet?
12. Can you have 2 VLANs on the same subnet?
13. How do I ping an IP address from a VLAN?

Does a VLAN have an IP address?

VLANs do not really have IP addresses assigned to them. They have a network assigned to them, or a subnet, or a network range, however you want to refer to it. The address the OP supplied us is an assignable address within the range of 192.168.

How do I find my VLAN details?

Use the show vlan command to verify your VLAN configuration. This command displays all switchports and their associated VLAN as well as the VLAN status and some extra parameters that relate to Token Ring and FDDI trunks. You can use the show vlan id [vlan#] command to see information about a particular VLAN.

What is a VLAN IP address?

Same thing, the VLANs IP address is a Switch Virtual Interface (commonly called a SVI), in essense it is an interface (albeit logical) and plays the same role as a routers interface which has an IP address. It provides a gateway for inter-VLAN or inter-routing traffic.

How many IP addresses are in a VLAN?

With it, you can get a single VLAN with 512 IP addresses. The decimal subnet mask for a /22 is 255.255. 252.0 and that'll give you 1,024 IP addresses.

Does native VLAN need IP address?

Routers use subinterfaces as the means to have an interface connected to a VLAN. The router needs to have an IP address/mask associated with each VLAN on the trunk.

How do I add a VLAN to my router?

To add a VLAN and enter config-VLAN submode on a switch, use the vlan command in global configuration mode. To name a VLAN on a switch, use the name command in VLAN configuration mode. To set the interface type, use the switchport mode command in interface configuration mode.

Does VLAN have default gateway?

The default gateway is the first Layer 3 device (such as a router) on the same management VLAN network to which the switch connects.

What is VLAN ID in router?

A VLAN represents a broadcast domain. VLANs are identified by a VLAN ID (a number between 0 – 4095), with the default VLAN on any network being VLAN 1. Each port on a switch or router can be assigned to be a member of a VLAN (i.e., to allow receiving and sending traffic on that VLAN).

Why do you assign an IP Address to a VLAN?

IP Address assigned to VLAN Interface is used for this purpose. Through L3 Switch can also do Routing operations ,IP Address assigned to VLAN Interface is used for remote access, Most switches would have a management interface as well for telnet and remote access.

What is VLAN in CCNA?

VLANs (Virtual LANs) are logical grouping of devices in the same broadcast domain. VLANs are usually configured on switches by placing some interfaces into one broadcast domain and some interfaces into another. Each VLAN acts as a subgroup of the switch ports in an Ethernet LAN.

Should I use VLAN or subnet?

Subnet has limited control in comparison to VLAN. VLAN is extremely flexible, it brings better work performance, less traffic, and more efficiency. A Subnet will not be affected when other Subnets going down or having technical breakdowns.

Can you have 2 VLANs on the same subnet?

1 Answer. Of course you can do that, but it is not the recommended way. VLANs use software to emulate separate physical LANs. Each VLAN is thus a separate broadcast domain and a separate network.

How do I ping an IP address from a VLAN?

Use a extended ping command by using the source address from an SVI interface you've created towards the IP address of the another SVI on this switch. Once these interfaces are up, and you have setup the IP addresses on the hosts belonging to them, you are able to see the ARP table for each L3 interface (SVI).