Refer to the exhibit which type of ipv6 static route is configured in the exhibit

Which type of IPv6 static route is configured in the exhibit? Answers Explanation & Hints: The route provided points to another address that must be looked up in the routing table. This makes the route a recursive static route.

1. What is a recursive IPv6 static route?
2. Which IPv6 static route is configured?
3. Which type of static route is configured with a greater administrative?
4. What is fully specified static route?
5. Why would a summarized static route be configured on a router?
6. When an IPv6 static route is configured it is possible that the same IPv6?
7. When an IPv6 static route is configured the next-hop address can be?
8. What characteristic completes the following statement when an IPv6 static route is configured?
9. Which option shows the correctly configured IPv4 default static route?
10. Which statement about static and dynamic routes is true?
11. Which type of static route is configured with a greater administrative distance to provide a backup route?
12. Which route will have the lowest administrative distance?

What is a recursive IPv6 static route?

In a next-hop/recursive static route, the IPv6 address of the neighboring router is specified. The output interface is derived from the next hop. Before any packet is forwarded by router, the routing table process must determine the exit interface to use to in order to forward the packet.

Which IPv6 static route is configured?

IPv6 also has a default static route similar to the IPv4 quad zero (0.0. 0.0) static default route. Instead, the IPv6 command uses the ::/0 notation to specify all networks. For example, a default static route as specified by the “::/0” entry is configured on router R2 to reach all other networks connected to R1.

Which type of static route is configured with a greater administrative?

A floating static route is configured with a higher administrative distance than the dynamic routing protocol it is backing up. As a result, the dynamic route learned through the routing protocol is always preferred to the floating static route.

What is fully specified static route?

In a fully specified static route, both the exit interface and the next-hop IP address are specified. This form of static route is used when the exit interface is a multi-access interface and it is necessary to explicitly identify the next hop. The next hop must be directly connected to the specified exit interface.

Why would a summarized static route be configured on a router?

Why would a summarized static route be configured on a router? A summary route represents multiple networks. A summarized static route does not necessarily provide a better route than a routing protocol does. A default static route would provide a default gateway for a router that is connected to an ISP.

When an IPv6 static route is configured it is possible that the same IPv6?

When an IPv6 static route is configured, it is possible that the same IPv6 link-local address is used for … a destination host route with a /128 prefix. the “ipv6 unicast-routing” command. the next-hop address of two different adjacent routers.

When an IPv6 static route is configured the next-hop address can be?

Multiple static or null routes to the same destination are not supported. The routing switches can concurrently support a maximum of 256 IPv6 static routes and 256 IPv4 static routes. Note: next-hop addresses can be either global unicast or link-local.

What characteristic completes the following statement when an IPv6 static route is configured?

When an IPv6 static route is configured, the installation of the route can be verified with …… the “show ipv6 route static” command.

Which option shows the correctly configured IPv4 default static route?

Which option shows a correctly configured IPv4 default static route? The static route ip route 0.0. 0.0 0.0. 0.0 S0/0/0 is considered a default static route and will match all destination networks.

Which statement about static and dynamic routes is true?

Which statement about static and dynamic routes is true? The correct answer is "Static routes are manually configured by a network administrator, whereas dynamic routes are automatically learned and adjusted by a routing protocol." A network administrator manually enters static routes into the router.

Which type of static route is configured with a greater administrative distance to provide a backup route?

Explanation: A backup static route is called a floating static route. A floating static route has an administrative distance greater than the administrative distance of another static route or dynamic route.

Which route will have the lowest administrative distance?

A directly connected will always have the lowest, at 0. A static route will always have an AD of 1, EIGRP is 90, and OSPF is 110.